睿地可靠度論壇(TW-REDI Forum)

標題: 書籍:Life Cycle Reliability Engineering (by Guangbin Yang) [打印本頁]

作者: hlperng    時間: 2014-10-28 20:42:37     標題: 書籍:Life Cycle Reliability Engineering (by Guangbin Yang)

本帖最後由 hlperng 於 2016-1-15 17:30 編輯

生命週期可靠度工程 (Life Cycle Reliability Engineering)
福特公司楊廣斌博士 (Dr. Guangbin Yang) 在 2007 年著作、John Wiley and Son, Inc 出版,以汽車可靠度為主題的教科書。


目錄 (Table of Contents)
1. Reliability Engineering and Produt Life Cycle
    1.1 Reliability Engineering
    1.2 Product Life Cycle
    1.3 Integration of Reliability Engineering into the Product Life Cycle
    1.4 Reliability in the Concurrent Product Realization Process
         Problems

2. Reliability Definition, Metrics, and Product Life Distributions
    2.1 Introduction
    2.2 Reliability Definition
    2.3 Reliability Metrics
    2.4 Exponential Distribution
    2.5 Weibull Distribution
    2.6 Mixed Weibull Distribution
    2.7 Smallest Extreme Value Distribution
    2.8 Normal Distribution
    2.9 Lognormal Distribution
         Problems

3. Reliability Planning and Specification
    3.1 Introduction
    3.2 Customer Expectations and Satisfaction
    3.3 Reliability Requirements
    3.4 Reliability Program Development
    3.5 Reliability Design and Design for Six Sigma
         Problems

4. System Reliability Evaluation and Allocation
    4.1 Introduction
    4.2 Reliability Block Diagram
    4.3 Series Systems
    4.4 Parallel Systems
    4.5 Mixed Configuration
    4.6 k-out-of-n Systems
    4.7 Redundant Systems
    4.8 Reliability Evaluation of Complex Systems
    4.9 Confidence Intervals for System Reliability
    4.10 Measures of Component Importance
    4.11 Reliability Allocation
           Problems

5. Reliability Improvement through Robust Design
    5.1 Introduction
    5.2 Reliability and Robustness
    5.3 Reliability Degradation and Quality Loss
    5.4 Robust Design Process
    5.5 Boundary Definition and Interaction Analysis
    5.6 P-Diagram
    5.7 Noise Effects Management
    5.8 Design of Experiments
    5.9 Experimental Life Data Analysis
    5.10 Experimental Degradation Data Analysis
    5.11 Design Optimization
    5.12 Robust Reliability Design of Diagnostic Systems
    5.13 Case Study
    5.14 Advanced Topics in Robust Design
           Problems

6. Potential Failure Mode Avoidance
    6.1 Introduction
    6.2 Failure Mode and Effects Analysis
    6.3 Advanced Topics in FMEA
    6.4 Fault Tree Analysis
    6.5 Advanced Topics in FTA
    6.6 Computer-Aided Design Controls
         Problems

7. Accelerated Life Tests
    7.1 Introduction
    7.2 Development of Test Plans
    7.3 Common Stresses and Their Effects
    7.4 Life-Stress Relationships
    7.5 Graphical Reliability Estimation at Individual Test Conditions
    7.6 Analytical Reliability Estimation at Individual Test Conditions
    7.7 Reliability Estimation at Use Condtion
    7.8 Compromise Test Plans
    7.9 Highly Accelerated Life Tests
         Problems

8. Degradation Testing and Analysis
    8.1 Introduction
    8.2 Determination of the Critical Performance Characteristic
    8.3 Reliability Estimation from Pseudolife
    8.4 Degradation Analysis with Random-Effects Models
    8.5 Degradation Analysis for Destructive Inspections
    8.6 Stress-Accelerated Degradation Tests
    8.7 Accelerated Degradation Tests with Tightened Thresholds
    8.8 Accelerated Degradation Test Planning
         Problems

9. Reliability Verification Testing
    9.1 Introduction
    9.2 Planning Reliability Verification Tests
    9.3 Bogey Testing
    9.4 Sample Size Reducing by Tail Testing
    9.5 Sequential Life Test
    9.6 Reliability Verification using Prior Information
    9.7 Reliability Verification through Degradation Testing
         Problems

10. Stress Screening
     10.1 Introduction
     10.2 Screening Techniques
     10.3 Design of Screen Plans
     10.4 Principle of Degradation Screening
     10.5 Part-Level Degradation Screening
     10.6 Module-Level Screening
     10.7 Module Reliability Modeling
     10.8 Cost Modeling
     10.9 Optimal Screen Plans
            Problems

11. Warranty Analysis
     11.1 Introduction
     11.2 Warranty Policies
     11.3 Warranty Data Mining
     11.4 Reliability Estimation from Warranty Chain Times
     11.5 Two-Dimensional Reliability Estimation
     11.6 Warranty Repair Modeling
     11.7 Warranty Cost Estimation
     11.8 Field Failure Monitoring
     11.9 Warranty Cost Reduction
            Problems

Appedix: Orthogonal Arrays, Linear Graphs, and Interaction Tables

References

Index


參考資料:


作者: hlperng    時間: 2014-10-28 22:08:00

本帖最後由 hlperng 於 2016-1-15 17:29 編輯

發現楊廣斌博士這本書是論壇討論 Bogey Test 議題時上網查詢獲得的資訊。

[attach]359[/attach](1964 - 2013)

楊廣斌博士 (Dr. Guangbin Yang, 1964 - 2013),1964 年 8 月 22 日生於廣東省揭西縣,1986 年獲得杭州電子工程學院機械工程學士,1989 年獲得浙江大學機械工程碩士學位,2000 年獲得美國 Wayne State University 工業工程博士學位。畢業後進入美國汽車業界,分別任職 Yazaki、Ford、Chrysler 等公司。楊博士不幸於 2013 年 6 月 13 日過世。詳見 Dr. Hoang Pham 2013 年發表的追悼文:Dr. Guangbin Yang (1964 - 2013)

作者: xxex    時間: 2014-10-29 11:19:18

这本书太经典了,可惜天妒英才




歡迎光臨 睿地可靠度論壇(TW-REDI Forum) (http://m1.kdi.tw/) Powered by Discuz! X2